# Parts List & Overview

## Parts List &amp; Overview

A DIY solar repeater can be built for roughly $90 - $140 using commodity parts (with the solar-capable Heltec V4; a stripped-down V3 build can come in lower). This build creates a weatherproof, autonomous LoRa mesh repeater powered entirely by solar with enough battery reserve to ride through multiple cloudy days. Prices below are approximate and parts-dependent, as of 2026-06-08; component prices drift over time, and totals exclude shipping.

### Full Parts List

<table id="bkmrk-componentrecommended"><thead><tr><th>Component</th><th>Recommended Option</th><th>Cost</th><th>Notes</th></tr></thead><tbody><tr><td>LoRa node</td><td>Heltec V3 *or* Heltec V4</td><td>V3 ~$20 - $35; V4 ~$45 - $50</td><td>Heltec V4 (~$45-50) added a built-in solar charge input and is preferred for solar builds; the older V3 (~$20-35) lacks it and needs an external charge controller. Prices as of 2026-06-08.</td></tr><tr><td>Alternative node</td><td>RAK WisBlock (RAK4631 + RAK19007)</td><td>~$31 - $35</td><td>RAK4631 core (~$21-23) + RAK19007 base (~$9.99) ≈ $31-35 combined (as of 2026-06-08). Lower power draw; more expensive than a bare Heltec V3 but the nRF52840 runs cooler.</td></tr><tr><td>Antenna</td><td>5 dBi fiberglass omni</td><td>$12 - $20</td><td>RAK 5.8 dBi fiberglass is a community favourite at ~$30 - $40 (prices as of 2026-06-08). Budget fiberglass omni gain figures are often marketing-inflated; treat quoted dBi as nominal and do not assume the full gain in link/EIRP calculations.</td></tr><tr><td>Coax pigtail</td><td>SMA pigtail, 15 - 30cm</td><td>$3 - $5</td><td>Match connector type to your node (SMA or RP-SMA). Note: RP-SMA is not more weather-resistant than SMA - they share the same body and thread, only pin polarity differs.</td></tr><tr><td>Solar panel</td><td>6W 6V monocrystalline</td><td>$15 - $20</td><td>A 6V panel matches the CN3791 6V variant directly; a TP4056 will also accept ~6V but is a linear (non-MPPT) charger, so the CN3791 is strongly preferred for solar. Commodity pricing as of 2026-06-08.</td></tr><tr><td>Battery</td><td>Samsung INR18650-35E 18650, ~3500mAh</td><td>~$10</td><td>Counterfeit and re-wrapped 18650 cells are common on open marketplaces - buy from a reputable battery vendor and avoid suspiciously cheap or overstated-capacity cells. Use a protected cell or pair with a BMS.</td></tr><tr><td>Charge controller</td><td>CN3791 MPPT module</td><td>$3 - $5</td><td>More efficient than TP4056; better for variable solar; supports 6V input (the CN3791 6V variant is matched to a 6V panel)</td></tr><tr><td>Inline fuse + holder</td><td>1 - 3 A inline fuse, sized to wiring</td><td>~$2</td><td>Place on the battery positive lead to protect against short-circuit fire. Reference the wiring order in the Assembly Guide.</td></tr><tr><td>Enclosure</td><td>Zulkit IP65 150×100×70mm</td><td>$12</td><td>Hinged lid; 2 cable glands included</td></tr><tr><td>Cable glands</td><td>PG7 (thin cables, ~3-6.5mm) or PG9 (coax, ~4-8mm)</td><td>$3 - $5</td><td>For antenna pigtail and solar wires entering enclosure</td></tr><tr><td>Mounting hardware</td><td>U-bolt + hose clamps or pole mount</td><td>$5 - $8</td><td>Stainless steel preferred for outdoor longevity</td></tr><tr><td>Desiccant</td><td>Silica gel packs 5g</td><td>$2</td><td>Place inside enclosure; replace or regenerate annually (regenerate indicating silica gel at ~120 °C for 2-3 hours)</td></tr><tr><td>Sealant &amp; misc</td><td>Silicone sealant, zip ties, heat shrink</td><td>$5</td><td>Seal cable glands and any penetrations</td></tr></tbody></table>

**Total estimated cost: ~$90 - $140** for a V4 solar build (as of 2026-06-08), depending on component choices. A bare-bones V3 build can come in lower. The total is the sum of the line-item ranges above and is traceable to them; it excludes shipping.

### Power Budget

Before building, verify the solar panel and battery are adequately sized for your location and expected traffic. The figures below are board- and config-dependent estimates (ESP32 with a screen draws more; nRF52/sleep configs draw less) - measure your own device for an accurate budget.

<table id="bkmrk-parametervaluenotes-"><thead><tr><th>Parameter</th><th>Value</th><th>Notes</th></tr></thead><tbody><tr><td>Average current draw</td><td>20 - 40 mA</td><td>Typical repeater with moderate traffic; board- and config-dependent</td></tr><tr><td>Daily energy use</td><td>~2.22 Wh/day (low-traffic)</td><td>25mA × 3.7V × 24h. This assumes the low end of the 20-40 mA range; at 40 mA daily use rises to ~3.55 Wh/day. Treat 2.22 Wh/day as a best-case low-traffic figure.</td></tr><tr><td>6W panel, 2.5 peak sun hours, 70% efficiency</td><td>10.5 Wh/day</td><td>~4.7× margin over low-traffic consumption - but this assumes the panel is clear and producing. For year-round North Dakota, multi-day snow cover and overcast strings can drop harvest near zero; size the battery for 5-7 days of no solar and use more than one cell.</td></tr><tr><td>Single 3500mAh 18650 capacity</td><td>12.95 Wh</td><td>3500mAh × 3.7V; covers ~5.8 days with no solar at low traffic. A single cell is marginal for harsh winters - prefer a multi-cell pack.</td></tr></tbody></table>

### Build Overview

The build has four main stages:

1. **Flash firmware** - flash MeshCore Repeater variant onto the node before sealing it in the enclosure
2. **Wire the power system** - solar panel → charge controller → battery → node, with an inline fuse on the battery positive lead. When wiring an MPPT-style controller, connect the battery to the controller *before* the solar panel so the controller can detect the system voltage.
3. **Weatherproof the enclosure** - cable glands, sealant, desiccant
4. **Mount and aim** - antenna orientation, solar panel angle

See the [Assembly Guide](https://wiki.meshamerica.com/books/diy-build-guides/page/assembly-guide) page for step-by-step wiring and mounting details.