Portable Go-Kit: Field-Deployable Mesh Node A go-kit is a self-contained, rapidly deployable mesh node in a single weather-resistant case. It powers up in under 2 minutes. Runtime depends entirely on the battery, the node role, and display use: with the 12V 20Ah LiFePO4 pack specified below, a low-power RAK4631 will run for many days to weeks (see the corrected Power Budget); a small portable pack in client mode would give the shorter 12-48 hour figures sometimes quoted for compact kits. Go-Kit Design Philosophy The go-kit must satisfy three constraints: One-bag portability: Everything fits in a carry-on-sized case. Target weight under 10 lbs including battery. Rapid deployment: Someone with basic training should be able to set it up correctly in under 5 minutes. 12+ hour autonomous operation: Sufficient for most emergency activations without resupply. Go-Kit Bill of Materials Component Choice Notes Case Pelican 1510 or Nanuk 935 Carry-on size, weatherproof. The Nanuk 935 is the carry-on equivalent of the Pelican 1510; the smaller Nanuk 910 holds far less and is not interchangeable. LoRa node RAK4631 WisBlock Lowest power; best for battery runtime Battery 20Ah LiFePO4 12V (Dakota Lithium or Battle Born) ~256 Wh (12.8V nominal × 20Ah). Powers the node via the buck converter below - this pack runs a RAK4631 for weeks, not hours. Fuse and disconnect required (see safety note). Inline fuse + disconnect Fuse holder sized to wiring + master switch Fuse the battery positive lead at the battery terminal and add a master disconnect (see safety note below). Charge controller Victron MPPT 75/10 12/24V solar charge controller for the 12V LiFePO4 pack. Requires a solar panel with Vmp well above battery voltage (nominal 12V panel, Vmp ~18V). 12V→5V buck/USB regulator 12V to 5V USB buck converter Required. The RAK4631 is a 3.3V nRF52 board powered via its USB/5V input - never feed 12V directly to the board. Wiring path: battery → fuse → MPPT → 12V bus → buck → 5V USB → RAK4631. Solar panel ~25W foldable, nominal 12V (Vmp ~18V) For extended deployments. Must have Vmp ~18V to work with the 75/10 on a 12V battery - a 5V USB-style panel will NOT work with this MPPT controller. Antenna 915 MHz-tuned antenna (BNC base) Use a proper 902-928 MHz antenna. A quarter-wave whip is only ~8 cm at 915 MHz; a generic 40 cm telescoping whip is non-resonant here (~1.2 wavelengths, high VSWR, poor performance). If you want collapsible, use one specifically tuned/loaded for the 902-928 MHz band. Antenna cable SMA to BNC, 3m Allows antenna placement away from case Display OLED on RAK1921 module Shows node status without phone Battery safety: A 20Ah LiFePO4 cell can deliver hundreds of amps into a short - an unfused lead in a metal-tooled kit is an arc-flash and burn hazard. Fuse the battery positive at the terminal (sized to the wiring), include a master disconnect, and secure the battery so it cannot shift and short against tools or the case. Power Budget RAK4631 system current depends heavily on role: - CLIENT / low-duty roles can average low single-digit to ~15 mA. - ROUTER / repeater role keeps the radio in continuous RX and disables sleep; community measurements report ~80-100 mA constant for a RAK19007 + RAK4631 in router mode. Measure your own setup before sizing. Battery energy (use the pack's real voltage): - 12V LiFePO4 (12.8V nominal) x 20Ah = ~256 Wh - Capacity-based runtime (voltage-independent): 20,000 mAh / I_avg * at 15 mA (low-duty): ~1,333 h theoretical * at 100 mA (router): ~200 h theoretical - Derate ~2x for self-discharge, conversion losses, and TX: roughly 600+ h low-duty, ~100 h in router role. For a 24-hour deployment: - Low-duty need: 24h * 15mA = 360 mAh - Router need: 24h * 100mA = 2,400 mAh - A 20Ah pack covers either easily; a 2Ah 18650 bank lasts ~5 days ONLY at ~15 mA - in router/repeater role (~100 mA) it lasts ~20 h. Measure your node's actual average current to size the pack. Deployment Checklist Place case on stable surface or tripod Extend or mount antenna (highest practical point - window, pole, rooftop) Connect antenna cable to node SMA connector Verify the battery positive lead is fused, then connect battery to charge controller; power the node through the 12V→5V buck regulator (never 12V direct to the board) Verify node powers on and OLED shows status Connect phone via Bluetooth and verify node joins network Send test message to confirm operation Note power level (if solar available, deploy panel south-facing) Labeling and Documentation Every component should be labeled inside the kit: Node ID and short name (on a label inside the lid) Channel key (in a sealed envelope or QR code sticker). Note: channel encryption is permitted for unlicensed Part 15 operation at stock RAK4631 power. It would be prohibited only if the kit were ever operated under an amateur (Part 97) license. Quick-start laminated card with 7 deployment steps Contact info for the kit owner Inventory list with last-check date