# MeshCore Device Compatibility

## MeshCore Device Compatibility

MeshCore is a lightweight mesh firmware optimised for LoRa networks. The following devices are supported as of early 2026 (the supported list changes - always check [flasher.meshcore.io](https://flasher.meshcore.io) for the latest list before purchasing hardware specifically for MeshCore).

### Supported Devices

<table id="bkmrk-devicemcunotes-helte"><thead><tr><th>Device</th><th>MCU</th><th>Notes</th></tr></thead><tbody><tr><td>Heltec V3</td><td>ESP32-S3</td><td>Most popular beginner choice; stock BT antenna issue (see [Budget Devices](https://wiki.meshamerica.com/books/hardware-guide/page/budget-devices) page)</td></tr><tr><td>Heltec V4</td><td>ESP32-S3</td><td>~22 dBm (confirm against Heltec's current spec - some sources cite 28 dBm via an integrated PA, others ~22 dBm); solar charging interface</td></tr><tr><td>Heltec T114</td><td>nRF52840</td><td>Lower power than ESP32; DFU (double-tap) flashing</td></tr><tr><td>Heltec Wireless Paper</td><td>ESP32-S3</td><td>E-ink display (250×122); ~20 µA deep sleep (figure quoted for Heltec's V4; verify against the Wireless Paper datasheet)</td></tr><tr><td>LilyGo T-Beam</td><td>ESP32</td><td>GPS built-in; 18650 holder</td></tr><tr><td>LilyGo T-Deck</td><td>ESP32-S3</td><td>QWERTY + touchscreen standalone node</td></tr><tr><td>LilyGo T-Echo</td><td>nRF52840</td><td>E-ink + GPS + NFC; ~850 mAh internal battery (~5 - 7 day runtime)</td></tr><tr><td>RAK4631 (WisBlock)</td><td>nRF52840</td><td>Modular platform; DFU flashing</td></tr><tr><td>Wio Tracker L1</td><td>nRF52840</td><td>OLED + GPS; bare board</td></tr><tr><td>Wio Tracker L1 Lite</td><td>nRF52840</td><td>Most affordable Wio option; includes L76K GPS (drops the OLED screen vs the standard L1, not GPS)</td></tr><tr><td>Wio Tracker L1 Pro</td><td>nRF52840</td><td>Rugged enclosed, GPS, built-in battery</td></tr><tr><td>SenseCAP T1000-E</td><td>nRF52840</td><td>Credit-card size, IP65, GPS; LR1110 radio</td></tr><tr><td>Station G2</td><td>ESP32-S3</td><td>High-power base station (SX1262 + 35 dBm PA + LNA, ~36.5 dBm US915 output). Note: 36.5 dBm conducted exceeds the US FCC Part 15.247 30 dBm conducted limit; full-power US use requires amateur Part 97. See Base Station Nodes.</td></tr></tbody></table>

### Firmware Variants

When flashing MeshCore you choose a firmware variant:

- **Companion:** Personal device that pairs with a phone app over BLE or USB.
- **Repeater:** Autonomous mesh relay node; no user interaction needed after setup.
- **Room Server:** Acts as a message store-and-forward hub for a channel.

### nRF52 vs ESP32 Considerations

nRF52840-based devices (T-Echo, T114, RAK4631, Wio series, SenseCAP T1000-E) draw significantly less power than ESP32 equivalents, making them better suited for battery-critical deployments. The trade-off is a different flashing workflow: nRF52 devices typically use USB DFU with a double-tap reset (the UF2/USB DFU bootloader) rather than the BOOT-button (esptool) bootloader used on ESP32 boards. See the [Meshtastic nRF52 flashing docs](https://meshtastic.org/docs/getting-started/flashing-firmware/nrf52/).