DIY Build Guides
Step-by-step guides for assembling your own LoRa mesh nodes and repeaters.
📖 Start Here — DIY Build Guides
This book covers hands-on builds: flashing firmware, assembling nodes, weatherproofing outdoor de...
Firmware Flashing
Flashing MeshCore Firmware
Flashing MeshCore Firmware MeshCore firmware can be installed via the web flasher (easiest), with...
Flashing Meshtastic Firmware
Flashing Meshtastic Firmware Meshtastic firmware is flashed via the web flasher at flasher.meshta...
Flashing Troubleshooting
Flashing Troubleshooting Most flashing failures fall into a small set of categories. Work through...
JadeNode Build (~$50)
The JadeNode is one of CascadiaMesh's low-cost (~$50) DIY repeater designs, configured for the st...
Raccoon Tree Node Build (~$190)
The Raccoon Tree Node is a long-range forest repeater designed to be suspended from a tree branch...
1 Watt Ikoka Box Build
The Ikoka Box is a high-mounted infrastructure repeater design intended for fixed installations -...
Solar Repeater Build
Parts List & Overview
Parts List & Overview A DIY solar repeater can be built for roughly $90 - $140 using commodity pa...
Assembly Guide
Assembly Guide This guide assumes you have all parts from the Parts List & Overview page and have...
Cold Weather & Winter Operation
Cold Weather & Winter Operation LoRa mesh nodes can operate year-round in cold climates, but cold...
Enclosures
Device-Specific Setup Guides
Heltec V3 Setup Guide
⚠ ANTENNA SAFETY - ALL DEVICES: Always connect a proper 915 MHz antenna (or a 50-ohm dummy load)...
Heltec V4 Setup Guide
⚠ ANTENNA SAFETY: Always connect a proper 915 MHz antenna (or a 50-ohm dummy load) before transm...
LilyGo T-Echo Setup Guide
⚠ ANTENNA SAFETY - ALL DEVICES: Always connect an antenna before powering on or transmitting wit...
LilyGo T-Beam Setup Guide
⚠ ANTENNA SAFETY - ALL DEVICES: Always connect an antenna before powering on or transmitting with...
LilyGo T-Deck Setup Guide
⚠ ANTENNA SAFETY - GOOD PRACTICE: Always connect an antenna before powering on or transmitting wi...
LilyGo T-Deck Plus Setup Guide
⚠ ANTENNA SAFETY - ALL DEVICES: As good practice, always connect an antenna before powering on or...
Station G2 Setup Guide
⚠ ANTENNA SAFETY - ALL DEVICES: Always connect a properly matched antenna before powering on any ...
Seeed Wio Tracker Setup Guide
⚠ ANTENNA SAFETY - ALL DEVICES: Always connect an antenna before powering on or transmitting with...
Nano G2 Ultra Setup Guide
⚠ ANTENNA SAFETY - ALL DEVICES: Always connect an antenna (or a 50-ohm dummy load) before transmi...
Popular Board Build Guides
Step-by-step build guides for the most common LoRa mesh hardware platforms.
T-Beam Build Guide (TTGO/LilyGO)
Overview The TTGO/LilyGO T-Beam is one of the most popular all-in-one LoRa mesh boards available....
Heltec LoRa 32 Build Guide
Overview The Heltec LoRa 32 is a compact, low-cost development board combining an ESP32-family mi...
RAK4631 WisBlock Build Guide
Overview The RAK WisBlock system is a modular hardware platform built around small snap-together ...
Enclosures & Weatherproofing
Guidance on selecting enclosures, IP ratings, cable management, and keeping your outdoor nodes re...
Complete Build Walkthroughs
End-to-end build guides for common repeater and gateway configurations, from budget solar nodes t...
Budget Solar Repeater Build (~$80)
This guide walks through assembling a low-cost, outdoor solar-powered LoRa repeater using the RAK...
High-Power Mountain Repeater Build (~$200)
⚠ FCC COMPLIANCE WARNING — READ BEFORE BUILDING: Under FCC Part 15 (47 CFR §15.247) the 902–928 M...
Rooftop Gateway Build (Pi + LoRa)
A rooftop gateway bridges your local LoRa mesh to the internet, enabling remote monitoring via me...
Enclosures and Weatherproofing
How to select, seal, and maintain outdoor enclosures for LoRa mesh nodes.
Weatherproofing Enclosures for Outdoor Nodes
Understanding IP RatingsIP (Ingress Protection) ratings are defined by IEC 60529 and describe how...
Mounting Outdoor Nodes - Poles, Walls, and Towers
Standard Mounting HardwareProper physical mounting is as important as weatherproofing for long-te...
3D Printing Enclosures for Meshtastic Nodes
Benefits vs. Pre-Made Enclosures3D-printed enclosures offer several advantages over off-the-shelf...
Enclosures and Weatherproofing
How to select, seal, and maintain outdoor enclosures for LoRa mesh nodes.
Choosing an Outdoor Enclosure
Picking the right enclosure is one of the most consequential decisions in any outdoor LoRa build....
Cable Glands and Penetrations
The gasket between the lid and body of your enclosure gets all the attention, but cable penetrati...
Condensation Management
A perfectly sealed enclosure with no cable gland defects can still suffer moisture damage from co...
Thermal Management for Outdoor Enclosures
Heat is the silent killer of outdoor electronics. A node that operates flawlessly through rain an...
Practical Sealing Techniques
This page consolidates the step-by-step procedures for assembling and commissioning a sealed outd...