Skip to main content
Pitch In Subscribe

Flashing MeshCore Firmware

Flashing MeshCore Firmware

MeshCore firmware can be installed via the web flasher (easiest), with command-line flashing tools (esptool for ESP32, UF2 drag-and-drop for nRF52), or OTA (over-the-air) for updates on already-running devices. All methods are covered below.

Method 1: Web Flasher (Recommended)

The web flasher at flasher.meshcore.co.ukio (the canonical URL;flasher, run by the .ioMeshCore aliascore mayteam resolveand butlinked isfrom notthe official docs - URL accurate as of 2026-06-08)13) requires a Chromium-based browser (Chrome or Edge). Firefox does not support the WebSerial API and will not work. Note: flasher.meshcore.co.uk is a separate, downstream flasher associated with the MeshOS variant - for standard MeshCore, use flasher.meshcore.io.

  1. Open flasher.meshcore.co.ukio in Chrome or Edge.
  2. Connect your device via USB. Use a data-capable USB cable. Charge-only cables (common with power banks) will not expose the serial port. If the device does not appear, try a different cable first.
  3. Hold the BOOT button while plugging in (ESP32 devices) or double-tap the reset button (nRF52 devices) to enter bootloader mode.
  4. Select your device type from the dropdown.
  5. Select the firmware variant:
    • Companion - pairs with a phone app over BLE or USB
    • Repeater - autonomous relay node, no interaction needed
    • Room Server - store-and-forward message hub
  6. Click Flash. The process takes 1 - 2 minutes. Do not disconnect during flashing.
  7. After flashing completes, configure the device via the MeshCore app or CLI.

Method 2: Command-Line Flashing

Note: meshcore-cli does not flash firmware - it connects to an already-running node to configure and interact with it (see Post-Flash Configuration below). Command-line flashing uses the standard chip-flashing tools instead, which is useful for bulk deployments or when the web flasher is unavailable.

ESP32 boards (V3, T-Beam, Station G2, etc.) - esptool: Install Python 3 first, then install esptool. On many systems use pip3 if pip is not found; on recent Linux/macOS a bare system pip install is blocked (PEP 668), so use a virtual environment or pipx:

pip3 install esptool   # or: pipx install esptool

Put the board in bootloader mode (hold BOOT while connecting USB), then write the MeshCore merged firmware .bin. Replace the port and filename to match your system:

esptool.py --port COM3 write_flash 0x0 meshcore-firmware.bin       # Windows
esptool.py --port /dev/ttyUSB0 write_flash 0x0 meshcore-firmware.bin  # Linux/macOS

nRF52 boards (RAK4631, Heltec T114, T-Echo, etc.) - UF2 drag-and-drop: Double-tap the reset button to enter the UF2 bootloader. The board appears as a USB mass-storage drive; copy the MeshCore .uf2 file onto that drive. The board flashes and reboots automatically. No command-line tool is required.

Method 3: OTA Update (ESP32 devices only)devices)

For devices already running MeshCore firmware, OTA updates avoid needing a USB connection. ESP32 boards update over a temporary Wi-Fi access point. See Flashing MeshCore Firmware OTA: The Definitive Guide in the MeshCore book for the full walkthrough.

  1. In the MeshCore app, open the Command Line for your device.
  2. Type: start ota
  3. The device will create a Wi-Fi hotspot named MeshCore-OTA (it may appear as "MeshCore OTAOTA").
  4. Connect your phone or computer to the MeshCore OTAthat Wi-Fi network.
  5. Open a browser and navigate to http://192.168.4.1/update
  6. Upload the newnon-merged firmware file (.bin) - not the merged .bin, which is for first-time USB flashing. Wait for the device to reboot.

Method 4: OTA Update (nRF52 devices)

nRF52-based devices use the Nordic DFU protocol for OTA updates. Installing the OTAFIX bootloader (from flasher.meshcore.io) first makes BLE OTA far more reliable. See Flashing MeshCore Firmware OTA: The Definitive Guide for the full walkthrough.

  1. InPlace the MeshCoredevice app,in typeOTA DFU mode (with OTAFIX installed, hold the button while resetting; otherwise issue start ota in the MeshCore app Command Line.Line).
  2. Use the nRF Device Firmware Update app (available for Android/iOS)iOS; it appears as "DFU" in your app list).
  3. Select the firmware .zip DFU package and transfer. The standard DFU flow handles transfer automatically; leave the app's transfer/packet-receipt settings at their defaults unless the MeshCore release notes for your board specify otherwise.

Bootloader Entry by Device

DeviceMethod
Most ESP32 devices (V3, V4, T-Beam)Hold BOOT button while connecting USB
nRF52 (T-Echo, RAK WisBlock, Wio series)Double-tap reset button quickly
LilyGo T-Deck variantsDepress trackball while connecting USB
Heltec V3Uses a CP2102 USB-serial bridge - install the Silicon Labs CP210x driver first
Heltec V4Native USB CDC (the CP2102 was removed on V4) - no external USB-serial driver needed

Post-Flash Configuration (meshcore-cli)

After flashing, the device needs basic configuration before it will function on the network. You can configure it from the MeshCore app, or from a terminal with meshcore-cli, which connects to a running node (it does not flash firmware). Install it with pip3 install meshcore-cli (use a venv or pipx on PEP 668 systems), then connect using one of:

meshcore-cli -s COM3            # serial (Windows); use -s /dev/ttyUSB0 on Linux/macOS
meshcore-cli -a <BLE address>   # BLE by address (or -S to scan and pick from a selector)
meshcore-cli -t 192.168.1.100 -p 5000   # TCP/IP (default port 5000)

Then set the basics:

  • Set device name (used to identify you in the mesh)
  • Set region/frequency. For North America select the US region: this constrains the radio to the 902-928 MHz band (commonly shorthanded "915 MHz") and is the primary compliance control - the US region preset enforces the band edges and caps TX power to the FCC Part 15 limit. Do not select a non-US region or disable the cap.
  • Set TX power. For unlicensed US operation, conducted output must not exceed 30 dBm (1 W) and must be reduced further for antennas above 6 dBi (so total EIRP stays within the 36 dBm / 47 CFR 15.247 ceiling). The US region preset normally caps power correctly, but verify on high-power hardware (e.g. Station G2 or 2 W modules), which can default or be set above the legal limit. Reduce power for indoor testing.
  • For Repeater variant: set the repeater name and ensure auto-start is enabled
Back to top