Rooftop Gateway Build (Pi + LoRa)

A rooftop gateway bridges your local LoRa mesh to the internet, enabling remote monitoring via meshmap.net, MQTT integration with Home Assistant, and APRS forwarding. This build uses a Raspberry Pi Zero 2W paired with a USB-connected LoRa node as the simplest, most maintainable approach.

Parts List

Part	Approx. Cost
Raspberry Pi Zero 2W	~$15
Heltec LoRa 32 V3 (SX1262, USB-C) - acts as the LoRa radio	~$2015 - $25 (street price varies; as of 2026-06-08)

LoRa antenna (915 MHz, SMA, matched to the Heltec) + pigtail~$8 - $15 5V PoE splitter (802.3af to micro-USB/USB-C) or USB power supply~$10 MicroSD card, 16 GB (Class 10 / A1 or better)~$8 Weatherproof outdoor enclosure (IP65 or better, fits Pi + Heltec) - light-colored / shaded~$25 Short USB-A to USB-C cable (internal, ~15 cm)~$3 Total~$8184 - 100115 (estimate, subject to current street pricing)

Connect the antenna to the Heltec before powering it on (good practice for any LoRa radio). Thermal note: a sealed enclosure in direct rooftop sun can reach 70-80 °C internally - well above a Raspberry Pi's reliable operating range and hard on SD-card lifespan. Use a light-colored or white enclosure, mount it in shade where possible, and add rain-protected ventilation. See the Thermal Management for Outdoor Enclosures page for details.

Alternative radio option: For LoRaWAN instead of Meshtastic, substitute the Heltec with a RAK2287 Pi HAT (SX1302 8-channel concentrator, ~$80)80 as of 2026-06-08) and use the ChirpStack network server. This guide focuses on the Meshtastic MQTT gateway path.

Setup: Meshtastic MQTT Gateway

1. Prepare the Pi

Flash Raspberry Pi OS Lite (64-bit) to the microSD card using Raspberry Pi Imager. In the Imager advanced settings, pre-configure your Wi-Fi credentials, enable SSH, and set a hostname (e.g. mesh-gateway). This avoids needing a display or keyboard on first boot.

2. Connect the Heltec

Connect the Heltec LoRa 32 V3 to the Pi Zero 2W via the short USB-C cable. The Pi will enumerate the Heltec as a USB serial devicedevice. atThe Heltec V3's USB-serial bridge usually appears as /dev/ttyUSB0 or(native-USB nRF boards appear as /dev/ttyACM0). Confirm which one you actually have with:

ls /dev/tty{USB,ACM}*

Important: In every command below, substitute the port you actually found here (shown as /dev/ttyXXX). If your Heltec appeared as /dev/ttyUSB0, use that instead of /dev/ttyACM0, or the commands will silently fail against the wrong port.

3. Install Software

sudo apt update && sudo apt upgrade -y
pip install meshtastic
sudo apt install -y mosquitto mosquitto-clients

4. Configure the Heltec via Meshtastic CLI

Connect to the node over USB serial and enable MQTT:MQTT. Note that uplink_enabled and downlink_enabled are per-channel settings (use --ch-index / --ch-set), not fields on the mqtt module:

# Replace /dev/ttyXXX with the port you found in step 2
# Set MQTT server to localhost (the Pi itself)
meshtastic --port /dev/ttyACM0ttyXXX --set mqtt.address localhost
meshtastic --port /dev/ttyACM0ttyXXX --set mqtt.enabled true
# Uplink/downlink are PER-CHANNEL - set them on the primary channel (index 0)
meshtastic --port /dev/ttyACM0ttyXXX --ch-index 0 --ch-set mqtt.uplink_enabled true
meshtastic --port /dev/ttyACM0ttyXXX --ch-index 0 --ch-set mqtt.downlink_enabled true
# Enable JSON output (optional, for Home Assistant compatibility)
meshtastic --port /dev/ttyACM0ttyXXX --set mqtt.json_enabled true

5. Configure Mosquitto

Edit /etc/mosquitto/mosquitto.conf. toUse addauthentication anby anonymousdefault local- listenerconfigure (or adda username/password authrather forthan security):an open anonymous listener:

listener 1883
allow_anonymous false
password_file /etc/mosquitto/passwd

Create the password file with sudo mosquitto_passwd -c /etc/mosquitto/passwd meshuser. An anonymous, unauthenticated broker (allow_anonymous true) is only acceptable on a fully trusted local network.

Restart Mosquitto:

sudo systemctl restart mosquitto
sudo systemctl enable mosquitto

6. Network Connectivity

Options in order of preference:

• PoE Ethernet: Use a PoE splitter to power the Pi over the same Ethernet cable that connects it to your router. Most reliable and simplest.
• Wi-Fi: The Pi Zero 2W has 2.4 GHz Wi-Fi. Works well if the rooftop is within range of your router. Add a second 2.4 GHz AP if needed.
• Ethernet-over-USB (USB gadget mode): Configure the Pi as a USB network adapter - plug a USB cable to a computer or router port. Useful when no other connectivity is available near the Pi.

7. Optional: Node-RED for Local Processing

bash <(curl -sL https://raw.githubusercontent.com/node-red/linux-installers/master/deb/update-nodejs-and-nodered)

Node-RED provides a visual flow editor for filtering, transforming, and routing mesh packets to Home Assistant, InfluxDB, or external webhooks without writing code.

8. Auto-Start on Boot (systemd)

Meshtastic'The Meshtastic node's own firmware MQTT bridgeclient runspublishes automatically whento the Heltecbroker is- pluggedthis happens on the node itself, not via a service on the Pi. For packets to publish, you need both mqtt.enabled = true and at least one channel with uplink_enabled = true (set in step 4). When both are in place and Mosquitto is running, so no custom systemd service is usuallyneeded; needed.but if you skipped the per-channel uplink step you will see no packets. If you add a custom Python script (e.g. for APRS forwarding), create a systemd service:

# /etc/systemd/system/mesh-bridge.service
[Unit]
Description=Mesh MQTT Bridge
After=network.target mosquitto.service
Requires=mosquitto.service

[Service]
ExecStart=/usr/bin/python3 /home/pi/mesh_bridge.py
Restart=always
RestartSec=10
User=pi

[Install]
WantedBy=multi-user.target

sudo systemctl enable mesh-bridge
sudo systemctl start mesh-bridge

9. Verify Packet Flow

Subscribe to all Meshtastic topics on the local broker and confirm packets are arriving:

mosquitto_sub -h localhost -t 'msh/#' -v

You should see JSON or binary payloads appearing whenever a node in range transmits. If nothing appears, check USB serial connectivity and MQTTthat settingsthe channel uplink is enabled on the Heltec.

Use Cases

• meshmap.net visibility: Configure Mosquitto to bridge to the public meshmap MQTT server so your nodes appear on the community map. See the meshmap.net documentation for bridge configuration details.
• Home Assistant integration: Use the Mosquitto add-on in Home Assistant and subscribe to msh/2/json/# for parsed telemetry and position data. Create automations triggered by mesh events.
• APRS gateway: Run aprx or a custom script to re-encode position packets as APRS-IS frames and upload to aprs.fi for interoperability with the ham radio APRS networknetwork. (Uploading to APRS-IS requires a valid amateur license)callsign and passcode. If you also gate this traffic onto APRS RF, Part 97 rules apply to the transmitted traffic - you must identify your station (97.119) and must not transmit encrypted content (97.113).
• Remote node monitoring: Query node telemetry via MQTT from anywhere on the internet to check battery voltage, SNR, and uptime of your remote repeaters. Access this over a VPN into your network rather than exposing the broker to the internet (see the security warning in step 5).