Skip to main content

Seeed Wio Tracker Setup Guide

⚠ ANTENNA SAFETY - ALL DEVICES: Always connect an antenna before powering on or transmitting with any LoRa device. Even a brief transmissionTransmitting without an antenna connected risks permanentcan damage to the LoRaradio. radioSX1262-based chip.boards (like the Wio Tracker) are relatively low-power and tolerate brief antenna mismatches better than older parts, and simply powering the board on without transmitting is generally harmless - but never deliberately transmit without an antenna connected.

Seeed Wio Tracker 1110L1 - Setup Guide

The Seeed Wio Tracker 1110 (also called the Wio Tracker L1)L1 is an nRF52840-based Meshtastic node with built-inan GPSSX1262 LoRa radio, an L76K multi-GNSS (GPS) module, and a 1.3" OLED display. The L1 Pro variant adds a ruggedan enclosure and 2000an mAhintegrated battery - strongly recommended for field deployment over the bare L1 board.

A note on naming, since Seeed's lineup is easy to confuse: the Wio Tracker L1 is the bare board used for this build; the L1 Pro is the L1 plus an enclosure and integrated battery. These are distinct from the separate Wio Tracker 1110, which is a different LR1110-based development board - it is not the same product as the L1, so match the exact name to the store listing before you buy.

Specifications

AttributeValue
MCUnRF52840
RadioSX1262
Display1.3" OLED
GPSBuilt-inL76K multi-GNSS module
Price (L1)$29.9032.99 (bare board, no enclosure, no battery) - Seeed store, as of 2026-06-08; prices drift, verify before buying
Price (L1 Pro)$42.9046.99 (rugged enclosure + 2000 mAhintegrated battery) - Seeed store, as of 2026-06-08; prices drift, verify before buying
StrengthsnRF52840 efficiency, GPS, OLED, longready-to-use battery life+ enclosure on L1 Pro
L1 vs L1 Pro - Which to Buy: The bare L1 board has no enclosure and no battery. Most users deploying in the field should choose the L1 Pro, which includesships as a ruggedready-to-use weatherproofnode with an enclosure and aan 2000 mAhintegrated battery.

Driver Installation

No driver installation required on any operating system. The nRF52840 presents as a USB mass storage device. It appears automatically on Windows, macOS, and Linux.

Entering Bootloader / DFU Mode

  1. Connect the device via USB.
  2. Locate the RESET button (may be recessed - use a SIM card ejector pin, toothpick, or similar small tool).
  3. Double-tap the RESET button quickly.
  4. The device will appear as a USB drive.

If the USB drive does not appear, retry the double-tap - timing sensitivity is similar to the T-Echo.

Firmware Flashing

Method A - Web Flasher (recommended):

  1. Enter DFU mode (double-tap RESET).
  2. Open Chrome or Edge and navigate to:
  3. Select the Wio Tracker L1 variant from the device list.
  4. Click Flash.

Method B - Drag and Drop:

  1. Download the .uf2 firmware file.
  2. Enter DFU mode.
  3. Drag and drop the .uf2 file onto the USB drive.
  4. Device reboots automatically.

Post-Flash Configuration

  1. GPS begins acquiring satellites automatically after boot.
  2. Connect via Bluetooth app and set region to US.
  3. Configure node name and channel settings.

Known Quirks

  • The RESET button may be recessed - have a SIM pin or similar tool available.
  • GPS first fix may take several minutes on a fresh boot outdoors.
  • L1 bare board requires an external battery and enclosure for practical field use.
Back to top